Difficulty
Moderate
Steps
10
Time Required
10 - 20 minutes
Sections
2
- Battery
- 7 steps
- Hard Drive
- 3 steps
Flags
0
BackHP Pavilion 11-n010dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Use the nylon spudger to remove the rubber pads near the hinge of the screen, then remove the screws under the pads.
- Use the Phillips #0 to remove four 9mm screws.
- Use the Phillips #0 to remove seven 6mm screws.
Use the nylon spudger to remove the rubber pads near the hinge of the screen, then remove the screws under the pads.
Use the Phillips #0 to remove four 9mm screws.
Use the Phillips #0 to remove seven 6mm screws.
1024
Step 2
- Use the nylon spudger to pry the back casing near the hinges for the screen.
- Continue to pry along the edge of the back case until the back is ready to be removed.
- Careful when beginning to remove the case. There is a cable attached between the bottom case and the motherboard that must be properly disconnected.
Use the nylon spudger to pry the back casing near the hinges for the screen.
Continue to pry along the edge of the back case until the back is ready to be removed.
Careful when beginning to remove the case. There is a cable attached between the bottom case and the motherboard that must be properly disconnected.
Step 3
- Use the blue plastic opening tool to lift up on the white tab that is holding the cable in place on the motherboard.
- Now carefully pull the cable out of place and remove the entire back casing.
Use the blue plastic opening tool to lift up on the white tab that is holding the cable in place on the motherboard.
Now carefully pull the cable out of place and remove the entire back casing.
Step 4
- Remove the five 6mm screws that hold the battery in place using the Phillips #0.
Remove the five 6mm screws that hold the battery in place using the Phillips #0.
Step 5
- Use the nylon spudger to pry away the blue/white wire that is positioned near your battery.
Use the nylon spudger to pry away the blue/white wire that is positioned near your battery.
Step 6
- Disconnect the battery cable from the motherboard by carefully pulling on the black wire at the point closest to the white tab.
Disconnect the battery cable from the motherboard by carefully pulling on the black wire at the point closest to the white tab.
Step 7
- Remove the battery from your device.
Remove the battery from your device.
Step 8
Hard Drive
- Use the Phillips #0 to remove the three 3mm screws holding the hard drive in place.
Use the Phillips #0 to remove the three 3mm screws holding the hard drive in place.
Step 9
- Carefully lift the hard drive out of place using the tag.
Carefully lift the hard drive out of place using the tag.
Step 10
- Gently pull on the cable connector to disconnect the hard drive from your device.
Gently pull on the cable connector to disconnect the hard drive from your device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 1 other contributor
Joseph Lintz
Member since: 09/15/2016
891 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
USF Tampa, Team 11-5, Blackwell Fall 2016
Member of USF Tampa, Team 11-5, Blackwell Fall 2016
USFT-BLACKWELL-F16S11G5
3 Members
5 Guides authored
Nicolas - Mar 25, 2020
Reply
Thanks a lot Joseph ! Works well for the model 11-n000nf !
Beverlyn - Nov 1, 2020
Reply
Thanks Joseph-I was able to get it open, disconnect the battery and ordered a new battery. We’ll see if this corrects the problem. Computer was sleeping for over a year. Thank you for your pictures and easy to follow instructions.
