Difficulty

Moderate

Steps

14

Time Required

                          30 minutes

Sections

3

  • Battery
  • 2 steps
  • Keyboard
  • 7 steps
  • Screen
  • 5 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHP Pavilion 14-v062us

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Power laptop off and make sure it is not plugged into charger
  • Push inward towards the center of laptop (it may take a lot of pressure). Battery should release once buttons are completely pushed in

Power laptop off and make sure it is not plugged into charger

Push inward towards the center of laptop (it may take a lot of pressure). Battery should release once buttons are completely pushed in

1024

Step 2

  • Lift the battery upwards and out from the laptop

Lift the battery upwards and out from the laptop

Step 3

              Keyboard
  • Remove rectangular rubber tops with a spudger
  • Remove the two 4.60 mm PH#1 screws located under rectangular rubber tops.
  • Remove plastic edge covering with the blue plastic opening tool.
  • Remove two 4.63 mm PH#1 screws located under plastic edge covering.

Remove rectangular rubber tops with a spudger

Remove the two 4.60 mm PH#1 screws located under rectangular rubber tops.

Remove plastic edge covering with the blue plastic opening tool.

Remove two 4.63 mm PH#1 screws located under plastic edge covering.

Step 4

  • Use Phillips screwdriver #1
  • Remove all nine 7.09 mm PH#1 screw black screws including small rectangular cover.
  • Remove the three 7.14 mm PH#1 screws.
  • Remove the one 7.09 mm PH#1 screw that will be underneath the small rectangular cover

Use Phillips screwdriver #1

Remove all nine 7.09 mm PH#1 screw black screws including small rectangular cover.

Remove the three 7.14 mm PH#1 screws.

Remove the one 7.09 mm PH#1 screw that will be underneath the small rectangular cover

Step 5

  • Remove disc tray
  • Locate screw within computer that is inside of where the disc tray was
  • Using a Phillips #1 screwdriver, unscrew the screw
  • Set laptop down and open laptop so the keyboard is facing you

Remove disc tray

Locate screw within computer that is inside of where the disc tray was

Using a Phillips #1 screwdriver, unscrew the screw

Set laptop down and open laptop so the keyboard is facing you

Step 6

  • Using a spudger or plastic opening tool, pry along siding of keyboard, where it connects to the rest of the laptop
  • Pry until you are able to lift entire face and keyboard
  • Only cables should be connecting it underneath

Using a spudger or plastic opening tool, pry along siding of keyboard, where it connects to the rest of the laptop

Pry until you are able to lift entire face and keyboard

Only cables should be connecting it underneath

Step 7

  • Disconnect/ unplug cables using plastic opening tool.
  • Separate the keyboard panel from the laptop with your hands.
  • Turn around the laptop and lay it flat.

Disconnect/ unplug cables using plastic opening tool.

Separate the keyboard panel from the laptop with your hands.

Turn around the laptop and lay it flat.

Step 8

  • Use a spudger to pry around the first layer of the silver panel until you are able to remove it
  • Only use a metal spudger as a last resort

Use a spudger to pry around the first layer of the silver panel until you are able to remove it

Only use a metal spudger as a last resort

Step 9

  • Using a spudger tool, start prying around the second layer of the silver panel until you are able to remove it
  • Only use a metal spudger as a last resort

Using a spudger tool, start prying around the second layer of the silver panel until you are able to remove it

Step 10

              Screen
  • Using the spudger, wedge tool in between screen and laptop
  • Only use a metal spudger as a last resort. A regular black nylon spudger or a plastic opening tool should be used whenever possible
  • Pry open screen with spudger and your hands

Using the spudger, wedge tool in between screen and laptop

Only use a metal spudger as a last resort. A regular black nylon spudger or a plastic opening tool should be used whenever possible

Pry open screen with spudger and your hands

Step 11

  • Remove the four 2.86 mm JIS#0 screws from each corner of the silver frame that is holding the digitizer.

Remove the four 2.86 mm JIS#0 screws from each corner of the silver frame that is holding the digitizer.

Step 12

  • Locate the white and brown wiring that connects to the digitizer and the screen.
  • Cut through the clear part of tape attached to the brown latch and white wiring.
  • Disconnect the wiring, by lifting the brown latch with the blue plastic opening tool and pulling the white wire at the same time.
  • Lift off the digitizer. If you need to replace the digitizer stop here and replace this part.
  • If you need to replace the screen, then continue

Locate the white and brown wiring that connects to the digitizer and the screen.

Cut through the clear part of tape attached to the brown latch and white wiring.

Disconnect the wiring, by lifting the brown latch with the blue plastic opening tool and pulling the white wire at the same time.

Lift off the digitizer. If you need to replace the digitizer stop here and replace this part.

If you need to replace the screen, then continue

Step 13

  • Remove the four 5.66 mm PH#0 from under the keyboard near the hinges.

Remove the four 5.66 mm PH#0 from under the keyboard near the hinges.

Step 14

  • Wedge spudger in between screen and back of computer
  • Only use a metal spudger as a last resort. A regular black nylon spudger or a plastic opening tool should be used whenever possible
  • Detach screen

Wedge spudger in between screen and back of computer

Detach screen

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors 


                    Lorena Esquivel

Member since: 09/27/2017

247 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Eastern Washington University, Team S1-G4, Carnegie Fall 2017                        

                                                  Member of Eastern Washington University, Team S1-G4, Carnegie Fall 2017 



                    EWU-CARNEGIE-F17S1G4                     


                                            3 Members                     


                                            4 Guides authored