Hp Pavilion 15 Cc123Cl Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Back Cover
2 steps
Battery
1 step
Screen
4 steps

Flags

BackHP Pavilion 15-cc123cl
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Before replacing any parts on your computer please refer to the troubleshooting page which may give you some solutions on how to fix your screen issues before buying a new one.

Make sure all power is fully disconnected before the rear laptop cover is removed.

What you need

Step 1

              Back Cover

Make sure to power off the laptop before proceeding with the guide.
Turn the laptop over so the back is facing up. Use a Phillips #0 screwdriver to remove the 11 screws from the bottom cover. Rotate the screws counter-clockwise.
Eight 5mm screws.
Three 10mm screws.

Make sure to power off the laptop before proceeding with the guide.

Turn the laptop over so the back is facing up. Use a Phillips #0 screwdriver to remove the 11 screws from the bottom cover. Rotate the screws counter-clockwise.

Eight 5mm screws.

Three 10mm screws.

1024

Step 2

Gently remove the CD-ROM drive by using a plastic opening tool and sliding it out of the laptop housing.
Using the opening tool, gently pry open the back panel of the laptop. Slowly work around the edge of the laptop with gentle pressure.
Remove the back cover from the laptop.

Gently remove the CD-ROM drive by using a plastic opening tool and sliding it out of the laptop housing.

Using the opening tool, gently pry open the back panel of the laptop. Slowly work around the edge of the laptop with gentle pressure.

Remove the back cover from the laptop.

Step 3

              Battery

Remove the six 5mm screws securing the battery using the Phillips #0 screwdriver.
Gently disconnect the battery from the motherboard with a plastic opening tool and remove it from the device.
If you’re installing a new battery, you should calibrate it after installation.
Charge it to 100% and continue to charge it for an additional two hours. Next, unplug the charger and use the laptop normally to completely drain the battery. Wait at least five hours and recharge the battery to 100%.

Remove the six 5mm screws securing the battery using the Phillips #0 screwdriver.

Gently disconnect the battery from the motherboard with a plastic opening tool and remove it from the device.

If you’re installing a new battery, you should calibrate it after installation.

Charge it to 100% and continue to charge it for an additional two hours. Next, unplug the charger and use the laptop normally to completely drain the battery. Wait at least five hours and recharge the battery to 100%.

Step 4

              Screen

Open the laptop and make sure the screen is facing you.
Insert a spudger or an opening tool in the top left corner and work your way around the edges of the screen to remove the black plastic bezel.
Using a metal spudger may severely damage the internal components in your device. In addition, using the metal spudger may crack the screen.

Open the laptop and make sure the screen is facing you.

Insert a spudger or an opening tool in the top left corner and work your way around the edges of the screen to remove the black plastic bezel.

Using a metal spudger may severely damage the internal components in your device. In addition, using the metal spudger may crack the screen.

Step 5

Remove the three screen chip 5.5mm screws using a Phillips #0 screwdriver.

Remove the three screen chip 5.5mm screws using a Phillips #0 screwdriver.

Step 6

Remove the four 5.5mm frame screws with a Phillips #0 screwdriver that secure the LCD panel.
Do not remove the screen after removing the screws.
Use a plastic opening tool to pry the screen away from the device.

Remove the four 5.5mm frame screws with a Phillips #0 screwdriver that secure the LCD panel.

Do not remove the screen after removing the screws.

Use a plastic opening tool to pry the screen away from the device.

Step 7

Gently peel back the clear tape holding the video connector.
Remove the video connector to fully remove the screen from the device.

Gently peel back the clear tape holding the video connector.

Remove the video connector to fully remove the screen from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Kodi Snapp

Member since: 09/08/2019

127 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Embry-Riddle Aeronautical University, Team S24-G1, McClure Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S24-G1, McClure Fall 2019 



                    ERAU-MCCLURE-F19S24G1                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team