Hp Pavilion 15 Cd040Wm Screen Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          30 minutes - 1 hour            

Sections

3

• HP Pavilion 15-cd040wm Back Cover Disassembly
• 3 steps
• Battery
• 2 steps
• Screen
• 3 steps

Flags

0

• BackHP Pavilion 15-cd040wm

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

To access the screen, you will first need to open your HP Pavilion 15-cd040wm by disassembling its back cover.

Before beginning, make sure to power off your laptop completely and disconnect it from any external power source. Once the back cover is off, be sure to disconnect the battery from the motherboard to ensure there is no power going to the laptop while it is being worked on.

What you need

Step 1

              HP Pavilion 15-cd040wm Back Cover Disassembly               

• The first step is to remove the four rubber non-slip pads on the bottom of the laptop to expose screws hidden underneath them. Peel off each tab with your fingers.
• If you have trouble gripping a tab, use a spudger to wedge it loose.

The first step is to remove the four rubber non-slip pads on the bottom of the laptop to expose screws hidden underneath them. Peel off each tab with your fingers.

If you have trouble gripping a tab, use a spudger to wedge it loose.

1024

Step 2

• 3x 10mm Phillips scews
• 2x 5mm Phillips screws
• 6x 6mm Phillips screws
• Remove all screws using a size Phillips #0 screwdriver.

3x 10mm Phillips scews

2x 5mm Phillips screws

6x 6mm Phillips screws

Remove all screws using a size Phillips #0 screwdriver.

Step 3

• Using the iFixit opening tool, carefully pry along the sides of the back cover.
• After all of the edges of the back cover have been freed, use your opening tool to carefully unclip the tabs holding the back cover to the CD drive.
• After everything is unclipped, you can safely remove the back cover from the rest of the device.

Using the iFixit opening tool, carefully pry along the sides of the back cover.

After all of the edges of the back cover have been freed, use your opening tool to carefully unclip the tabs holding the back cover to the CD drive.

After everything is unclipped, you can safely remove the back cover from the rest of the device.

Step 4

              Battery               

• 2x 5mm Philips screws
• 2x 3mm Philips screws
• Remove all screws using a size Phillips #0 screwdriver.

2x 5mm Philips screws

2x 3mm Philips screws

Step 5

• Gently pull up on the battery and tilt it away from the rest of the laptop chassis.
• Pull out the battery at an angle and lift it out of the laptop.

Gently pull up on the battery and tilt it away from the rest of the laptop chassis.

Pull out the battery at an angle and lift it out of the laptop.

Step 6

              Screen               

• Remove the four 6.0 mm screws from the hinges using a size Phillips #0 screwdriver.
• Use the iFixit opening tool to lift both of the hinges.

Remove the four 6.0 mm screws from the hinges using a size Phillips #0 screwdriver.

Use the iFixit opening tool to lift both of the hinges.

Step 7

• Using the spudger or opening tool, remove the ribbon that connects to the screen.
• Gently pull the ribbon out of the port after using the spudger to lift the supporter up.
• Carefully remove the two antenna wires that connect to the screen as well. Do this by gently pulling them free from their connectors at the wifi card.

Using the spudger or opening tool, remove the ribbon that connects to the screen.

Gently pull the ribbon out of the port after using the spudger to lift the supporter up.

Carefully remove the two antenna wires that connect to the screen as well. Do this by gently pulling them free from their connectors at the wifi card.

Step 8

• Once these steps are completed, you may lift the display assembly free from the rest of the device.

Once these steps are completed, you may lift the display assembly free from the rest of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Zachary Simao                     

Member since: 03/08/2019

405 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       UMass Dartmouth, Team S1-G1, Botvin Fall 2019                        

                                                  Member of UMass Dartmouth, Team S1-G1, Botvin Fall 2019 



                    UMASSD-BOTVIN-F19S1G1                     


                                            4 Members                     


                                            7 Guides authored