Difficulty
Difficult
Steps
16
Time Required
15 - 30 minutes
Sections
3
- Battery
- 2 steps
- CD Drive
- 2 steps
- Front Panel
- 12 steps
Flags
0
BackHP Pavilion 17-f004dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Before you remove the battery, make sure the laptop is powered off.
- Slide the black battery latches inward to remove the battery.
Before you remove the battery, make sure the laptop is powered off.
Slide the black battery latches inward to remove the battery.
1024
Step 2
- Pull the battery out towards you while your fingers are still holding the latches in place.
Pull the battery out towards you while your fingers are still holding the latches in place.
Step 3
CD Drive
- Remove one 7 mm screw with a Phillips #1 screwdriver.
Remove one 7 mm screw with a Phillips #1 screwdriver.
Step 4
- Use a metal spudger to push the CD drive out of its slot for removal.
Use a metal spudger to push the CD drive out of its slot for removal.
Step 5
Front Panel
- Remove fifteen 7 mm screws with a Phillips #1 screwdriver.
Remove fifteen 7 mm screws with a Phillips #1 screwdriver.
Step 6
- Remove the thin plastic cover using the flat metal spudger to expose another screw.
- Remove one 7 mm screw with a Phillips #0 screwdriver.
Remove the thin plastic cover using the flat metal spudger to expose another screw.
Remove one 7 mm screw with a Phillips #0 screwdriver.
Step 7
- Use a metal spudger to remove the rubber “feet” to expose two screws.
Use a metal spudger to remove the rubber “feet” to expose two screws.
Step 8
- Underneath each rubber foot, there is a screw.
- Use the Phillips #1 screwdriver to remove a 4.8 mm screw on each side.
Underneath each rubber foot, there is a screw.
Use the Phillips #1 screwdriver to remove a 4.8 mm screw on each side.
Step 9
- Remove the two black end caps to expose more screws.
- The end caps will require some force to remove.
Remove the two black end caps to expose more screws.
The end caps will require some force to remove.
Step 10
- Remove the following six screws with a Phillips #1 screwdriver:
- Two 7 mm screws.
- Two 7 mm screws.
- Two 4.8 mm screws.
Remove the following six screws with a Phillips #1 screwdriver:
Two 7 mm screws.
Two 4.8 mm screws.
Step 11
- Remove two 2.4 mm broadhead screws from the CD Drive bay with a Phillips #0 screwdriver.
Remove two 2.4 mm broadhead screws from the CD Drive bay with a Phillips #0 screwdriver.
Step 12
- Flip the laptop back over. Then, with the laptop open, move the plastic prying tool around the top cover to pry it from the enclosure.
Flip the laptop back over. Then, with the laptop open, move the plastic prying tool around the top cover to pry it from the enclosure.
Step 13
- Partially lift the top cover from the enclosure.
Partially lift the top cover from the enclosure.
Step 14
- Remove the ribbon connecting the power button to the motherboard.
Remove the ribbon connecting the power button to the motherboard.
Step 15
- Remove the ribbon connecting the mousepad to the motherboard.
Remove the ribbon connecting the mousepad to the motherboard.
Step 16
- Remove the ribbon connecting the keyboard to the motherboard.
- You may now fully lift the front panel from the rest of the laptop.
Remove the ribbon connecting the keyboard to the motherboard.
You may now fully lift the front panel from the rest of the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Allan Soria
Member since: 09/21/2016
566 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
UC Davis, Team 1-4, Oliver Fall 2016
Member of UC Davis, Team 1-4, Oliver Fall 2016
UCD-OLIVER-F16S1G4
4 Members
8 Guides authored
