Hp Pavilion 17 G192Dx Disassembly Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          5 - 10 minutes            

Sections

2

• Battery
• 3 steps
• HP Pavilion 17-g192dx Disassembly
• 7 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

• BackHP Pavilion 17-g192dx

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Turn off the laptop.
• Slide the battery lock to the right until you see the open lock symbol.

Turn off the laptop.

Slide the battery lock to the right until you see the open lock symbol.

1024

Step 2

• Slide the battery release to the left until the battery pops up.
• This may require significant force.

Slide the battery release to the left until the battery pops up.

This may require significant force.

Step 3

• Lift the battery up.

Lift the battery up.

Step 4

              HP Pavilion 17-g192dx Disassembly               

• Using the metal spudger, pry up the screw covers.

Using the metal spudger, pry up the screw covers.

Step 5

• Remove the fifteen 7mm screws holding the back casing on using the Phillips #00 screwdriver.

Remove the fifteen 7mm screws holding the back casing on using the Phillips #00 screwdriver.

Step 6

• Remove the 7mm screw holding the disc drive in place using the Phillips #00 head screwdriver.

Remove the 7mm screw holding the disc drive in place using the Phillips #00 head screwdriver.

Step 7

• Using an iFixit opening tool, push the disc drive away from the outer case.
• Once the disk drive is out far enough it easily slides out.

Using an iFixit opening tool, push the disc drive away from the outer case.

Once the disk drive is out far enough it easily slides out.

Step 8

• Remove the four 7mm screws holding the back resting plates on using the Phillips #00 screwdriver.
• Using a metal spudger lift up on the back resting plate until it pops off.

Remove the four 7mm screws holding the back resting plates on using the Phillips #00 screwdriver.

Using a metal spudger lift up on the back resting plate until it pops off.

Step 9

• Remove the two 7 mm screws behind the plate using a Phillips #00 screwdriver.

Remove the two 7 mm screws behind the plate using a Phillips #00 screwdriver.

Step 10

• Pry up on the case with an iFixit opening tool until you can feel a snap.
• Pry around the remainder until you can separate the case from the keyboard with your hands.
• Gently separate the two.

Pry up on the case with an iFixit opening tool until you can feel a snap.

Pry around the remainder until you can separate the case from the keyboard with your hands.

Gently separate the two.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Larry Christian                     

Member since: 09/20/2019

273 Reputation

                                      1 Guide authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       Embry-Riddle Aeronautical University, Team S2-G121, Watkins Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S2-G121, Watkins Fall 2019 



                    ERAU-WATKINS-F19S2G121                     


                                            3 Members                     


                                            6 Guides authored